Browse Helix Models and Effects

Helix currently supports 72 amplifier models, 194 effects, 37 speaker cab models, and 16 microphones. On top of all that you also have the ability to load Impulse Responses (IRs) that you can grab from free or paid sources. Go have fun.

Dynamic Room (Line 6 Original)

Dynamic Room, the Helix model of a Line 6 Original

Line 6 Original room reverb typically found in high-end studio rack reverbs.


  • Decay—Sets the decay of the reverb (0.1 sec ~ 3.0 sec)
  • Predelay—Determines the amount of delay heard before the signal enters the room. Can sometimes result in more definition between the dry and effected signals
  • Damping—Determines the frequency above which the reverb will be absorbed. For example, if your room is full of people wearing foam high school mascot costumes, more high frequencies would be absorbed than if the room were empty
  • Diffusion—Sets the amount of smearing between discrete echoes, sometimes resulting in a softer effected signal
  • MotRate—Motion Rate, or how quickly the room's shape may be changing, due to people moving, doors opening or closing, etc.
  • Mix—Controls the wet/dry mix of the reverb. When set to 0%, no reverb is heard; when set to 100%, no dry signal is heard
  • Low Freq—Sets the frequency below which the Low Gain parameter is applied
  • Low Gain—Sets the reverb time for frequencies below the Low Freq value. Values below 0.0dB mean the bass frequencies decay faster than the treble frequencies; values above 0.0dB mean the bass frequencies decay slower than the treble frequencies
  • Low Cut—Applies a low cut (or high pass) filter to the reverb, letting you remove the effected signal below a certain frequency
  • High Cut—Applies a high cut (or low pass) filter to the reverb, letting you remove the effected signal above a certain frequency
  • Level—Controls the overall output level of the block
  • Trails—When set to "Off," the reverb decay is instantly muted when the block is bypassed. When set to "On," the reverb continues to decay naturally when the block is bypassed or a different snapshot is selected

Description source: Line 6
Image source: Line 6


Warm Jazz Tone

Created this for playing bebop jazz standards. Meant to be used with humbucker in neck position.Video coming later :)

  • 👇 Downloads: 109
  • 🤘 Upvotes: 2
  • Member: Kalimar
  • Performance Type:
    Direct (Recording, Headphone, PA)


Speak the Name

testin 4 david

  • 👇 Downloads: 54
  • 🤘 Upvotes: 0
  • Member: Jhgrosse97
  • Performance Type:
    Direct (Recording, Headphone, PA)


Patch Performance
Type
Description Member 👇 Downloads 🤘 Upvotes
Warm Jazz Tone Direct (Recording, Headphone, PA) Created this for playing bebop jazz standards. Meant to be used with humbucker in neck position.Video coming later :) Kalimar 109 2
Speak the Name Direct (Recording, Headphone, PA) testin 4 david Jhgrosse97 54 0
Comments    

There are no comments for this yet.

Some Products That We Love

Brought to you by the Fluid Solo department of Commerce

Expand your effects with HX One

The HX One gives you the world of Line 6's effects in a compact pedal. It's a great addition to your pedalboard, giving you the ability to expand the processing power of your rig, whether or not you have an HX device or Pod Go already.

Expand your effects with HX One

Last seen at $300

Put Some Pedal Toppers On!

Pedal toppers make switching easier by giving you more surface area for your feet.

Put Some Pedal Toppers On!

Last seen around $9 for a ten-pack

Power your HX Stomp via USB

This handy cord allows you to power your HX Stomp from a USB port, so you can power it from a USB power bank or other power source.

Power your HX Stomp via USB

Last seen around $23